| STORE HOURS 9 TO 6 CDT GMT minus 5 hours Monday thru Friday (800) 338-8863 1 (906) 864-1437 |
| ORDERING INFORMATION: MINIMUM
ORDER: SHIPPING
POLICY: You MUST browse the Catalog area, and try to learn what you want. We no longer search our catalog for you. Have
this information ready: Make
sure you are in the catalog area for your kind of piano-- If you are confused, call us for assistance. If we do not answer the phone, we are probably here-- Just leave a message- we will
return your call (it may not be the same day). |
PIANO
REPAIR:
CENTER PIN REPAIR TOOLS
EXHAUSTIVE WORD INDEX OF THE WHOLE SITE:
Other
regulating and restoration tools can be seen
by hitting links at the bottom
of this page.
CENTER
PIN AND FLANGE SIZING AND LOOSENING TOOLS
Pin Vise-- Takes pins and tools from 0" to .118" in diameter
4 inches long-- Ideal for holding broach tools and center
pins-- This is an
improvement over our
old model-- Enhances control inserting pins into
flanges.
Nickel plated with steel jaws. Double
ended.
Replaces and improves on Old Part Number
15212 above graphic
Part Number-
SH149 $ 17.75
Pin
Vise-- One set of friction jaws--
Opening
from 0" to .052" diameter pins and tools
Part
Number- SH152 $ 27.50
Repinning Tool-- Hand Press-- Not shown in graphics
This tool is hand held. The flange is placed against the
bottom, and the
grip is squeezed
The pin is driven out of the flange and can be removed completely.
The new pin is driven in by the other end
of the tool.
Sturdy aluminum construction.
SH5501 $ 60.00
Replacement needles-- Each
SH5501N
$ 4.75
Use
a Center Pin, smallest size
Broach
Kit-- Covers the most common sizes--
Eight broaches from .048 to .055-- in wood handles
Instruction sheet included -- Carrying case included
Developed by P.T.G. member, Don Manino.
Broach has wire point tapering up to size needed
Near handle is a 1/2 inch section for roughed
for reaming the bushing felt. Taper burnishes.
These are needed to size new flange bushings,
fine for
adjustments made on site-- See
graphic at left.
Part Number
SH220 $ 75.00
Center
Pin Punch-- 3-1/4 inches long- Old number 16213
SH176
$ 15.00
Reamer-- Cornered-- For enlarging hole in flanges and other needs--
Can be used to remove threads in brass flanges so they can be used
in a Kimball
SH153 $ 14.25
Burnisher--
Part 15215 in the graphic
Burnish the felt bushing hole- Tapered from .046 to
.066 inches- 4 inches long
SH155 $ 14.25
Drill-- 7/64 inch-- To drill flange holes--
Handles SH149 or SH152 needed
Without handle
Old Part Number in above graphic 152165
SH71
$ 6.00
Rat Tail File-- Handles
SH149 or SH152 needed to use this tool
Open flange bushing holes with control- 4-3/8 inches long- 15217 in graphic SH154 $ 46.50
Center Pin wood case with marked brass covers-- See graphic above
Holds 12 common sizes and controls removing pins--
Old number above16098
Case
only
SH165 $ 43.50
Case loaded with 12 sizes of center
pins
SH165A $ 108.25
Hypo-Applicator--
Hypodermic type needle on 2 ounce plastic bottle--
Cover included-- This is the most pracitical applicator we
now carry.
This could also be used to apply
pin tightening fluids.
Use to dispense lubricants
and pin tightener
SH184 $
5.80
Plastic Oiler / Lubricant
Applicator--
Unbreakable squeeze
plastic bottle-- One ounce size-- 4 inches overall.
Dispenses lubricants, pin tightener, and liquid graphite. Cap included.
Can be used to deliver lubricants into the tight
flanges drop by drop.
Old Part Number 51095A
SH190
$ 12.95
OTHER TOOLS FOR REPAIR AND RESTORATION:
GENERAL REGULATING AND REPAIR TOOLS
ORDER BY PHONE WITH CREDIT CARD
CALL
TOLL FREE: (800) 338-8863
If there is no answer, please leave
a message- we do answer our voicemail
OR:
Go to Mail Order Form for printing:
Online help available
BACK TO PIANO TITLE PAGE